High value MIG welder online store? We have a lot posts on this topic, you can use the search form of this piece doesn’t answer your questions.
The MIG welder performance depends on several parameters. The duty cycle is among them. It means the percentage of a 10-minute period the welder can work until it gets overheated. For example, “90A / 20%” means that a welder can work for 2 minutes at 90A before an 8-minute cooldown, i.e. 20% of 10 minutes. Now, about the material. We should note that the maximum thickness of a material a welder can handle depends on its amperage and welding wire thickness. Lastly, consider the thickness of the joint a welder can make in a single run. Household models can weld metal sheets from 18-gauge to 1/4” thick at the output of 70A – 180A, respectively.
How to pick a welder tips: Duty cycle: The advertised amperage of the machine offers a headline guide, but the duty cycle of the machine gives up the truth. Light industrial machine duty cycles can be as low as 20%, but more heavy duty MIG’s should range between 40-60%. If a 300amp MIG has 30% duty cycle for instance, it’s on the edge of acceptability. Duty cycle is determined by how many minutes out of 10, it can weld at 100%. Duty cycle testing: MIGS tested at 20 Degrees & 40 Degrees we consider good. (Beware any manufacturer who doesn’t quote an ambient temperature for testing) Manufacturer’s warranty: Always a great guide to quality. A three year warranty is good. Weld characteristics: Make sure the arc is smooth & suits your application. (Some machines are better suited at the low range and others at higher amperage range).
One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding.
Several tips on welding equipment, MIG and TIG welders, plasma cutters. Flat-Position Welding Increases Welding Speed : It’s common knowledge that welding in a horizontal position will be the easiest and fastest way to weld. A flat position is not as taxing to maintain and the welding puddle will stay in place. Take some time to evaluate each project before beginning in order to make sure the majority of welds can be completed in this position. If a job calls for vertical welding, see this article about vertical welding. Core Wire Feeder Increases TIG Welding Speed: For professional welders hoping to speed up TIG welding, a core wire feeder will add filler metal through an automated process. Watch this video on how it works. This enables welders to work with both hands and to maintain a constant flow of wire into the welding puddle. Ed Craig at the Frabricator writes about the wire feeder process first developed in Europe, saying it is “suitable for all-position welding on materials of any thickness, the process addresses traditional GTAW limitations and can enhance both manual and automated TIG weld quality and productivity.” Read more details on MIG Welders Online Shopping.
USA market pick: LONGEVITY Inc is a company that has been around since only 2001. Like LOTOS Technology, it still produces a fine enough quality welder that it has earned its spot on this list. Besides the gas cylinder, this welder comes with everything you need to get started and is simple to set up. With all this, along with its solid performance, this machine is marked at a fair price of under $400. Though it is manufactured in China, the LONGEVITY Migweld is still a quality welder. It is most well-adapted to light use. Compared to Miller and Hobart’s machines, the price is somewhat better without sacrificing much quality. It welds from 24 gauge to ¼ inches of steel. Flux core is available for this welder. The LONGEVITY can run at ten different voltage settings. As an added bonus, it has thermal overload protection like the LOTOS welder.
Forney have built a simple, mid range MIG welder that’s solid and reliable. It has some good power for the price but doesn’t have as good a duty cycle as the Hobart 190 or Lincoln 180. Forney aren’t one of the big three brands but this machine is still solidly built and I’d feel comfortable buying this. If you want a basic 220v welder without any special features, this is a good choice. Read the full review here.